Used DBX 1066 Compressor - Limiter - Gate
- Input Connectors:XLR and 1/4" TRS (Pin 2 and tip hot)
- Input Type:Electronically balanced/unbalanced, RF filtered
- Input Impedance:Balanced > 50 kOhm, unbalanced >25 kOhm
- Max Input:> +24 dBu balanced or unbalanced
- CMRR:Typically >50 dB at 1 kHz
- Output Connectors:XLR and 1/4" TRS (Pin 2 and tip hot)
- Output Type:Servo-balanced/unbalanced, RF filtered
- Output Impedance:Balanced 120 Ohm, unbalanced 60 Ohm
- Max Output:> +21 dBm balanced, > +20 dBm unbalanced
- Sidechain Input Connector:1/4" Unbalanced (Tip-Sleeve)
- Sidechain Input Type:Unbalanced, RF filtered
- Sidechain Impedance:>10 kOhm
- Sidechain Max Input Level:>+24 dBu
- Sidechain Output Connector:1/4" Balanced TRS (tip hot)
- Sidechain Output Type:Impedance balanced, RF filtered
- Sidechain Output Impedance:Balanced 2 kOhm, unbalanced 1 kOhm
- Sidechain Max Output Level:>+21 dBu balanced or unbalanced
- Bandwidth:20 Hz to 20 kHz, +0/0.5 dB
- Frequency Response:0.35 Hz to 90 kHz, +0/-3 dB
- Noise:< -95 dBu, unweighted, 22 kHz measurement bandwidth
- Dynamic Range:> 118dB, unweighted
- THD+Noise:0.008% typical at +4 dBu (1 kHz unity gain), 0.08% typical at +20 dBu (1 kHz unity gain), < 0.1% any amount of compression up to 40 dB, 1 kHz
- IMD:< 0.1% SMPTE
- Interchannel Crosstalk:< -80 dB 20Hz to 20 kHz
- Stereo Coupling:True RMS Power Summing
- Compressor Threshold Range:-40 dBu to +20 dBu
- Compressor Ratio:1:1 to infinity:1
- Compressor Threshold Characteristic:Selectable OverEasy® or hard knee
- Compressor Attack/Release Characteristic:AutoDynamic™
- Compressor Attack/Release Modes:Selectable Manual or Auto
- Compressor Manual Attack Time:Scalable program-dependent
- Compressor Manual Release Time:Scalable program-dependent
- Compressor Auto Attack Time:Program-dependent
- Compressor Auto Release Time:Program-dependent
- Compressor Output Gain:-20 to +20 dB
- Limiter Threshold Range:+4 dBu to +24 dBu (off)
- Limiter Ratio:infinity:1
- Limiter Type:PeakStopPlus® two-stage limiter
- Limiter Stage 1:PeakStop® brickwall limiter
- Limiter Stage 1 Attack Time:Zero
- Limiter Stage 1 Release Time:Zero
- Limiter Stage 2:Predictive intelligent program limiter
- Limiter Stage 2 Attack Time:Program-dependent
- Limiter Stage 2 Release Time:Program-dependent
- Expander/Gate Threshold Range:Off to +15dBu
- Expander/Gate Ratio:1:1 to 30:1
- Expander/Gate Attack Time:< 100 µsec
- Expander/Gate Release Time:Program-dependent
- SC Ext. Switch:Routes the external sidechain input signal to the detector
- SC Mon. Switch:Routes the sidechain signal to the output, interrupting the normal audio
- OverEasy® Switch:Activates the OverEasy compression function
- Countour Switch:Activates the frequency-dependent detector function
- Auto Switch:Activates automatic program-dependent attack and release times, disabling the manual Attack and Release controls
- I/O Meter Switch:Switches between monitoring input and output levels on the Input/Output Level meter
- Bypass Switch:Activates the direct input-to-output hard-wire relay bypass. Relay automatically hard-wire bypasses unit at power-down and provides a power-on delay of 1.5 sec.
- Operating Level Switch:(rear panel)Switches the nominal operating level between -10 dBV and +4 dBu simultaneoulsy for both input and output levels
- ST Link Switch:Link both channels for stereo operation. Channel One becomes the master
- Gain Reduction Meter:12-segment LED bar graph at 1, 2, 4, 6, 9, 12, 15, 18, 21, 24, 27 and 30 dB
- I/O Meter:8-segment LED bar graph at -24, -18, -12, -6, 0, +6, +12, and +18 dBu
- Compressor Threshold Meter:3-segment LED bar graph at Below (-), OverEasy and Above (+)
- Expander/Gate Threshold Meter:2-segment LED bar graph at Below (-) and Above (+)
- Limiter Threshold Meter:1 LED to indicate PeakStopPlus™ limiting
- Function Switches:LED indicator for each front-panel switch
- Output Transformer Options:Jensen® JT-123-dbx or JT-11-dbx, BCI RE-123-dbx or RE-11-dbx
- Operating Voltage:100-120 VAC 50/60 Hz 200-240 VAC 50/60 Hz
- Power Consumption:20 Watts
No reviews found